How to thread a sewing machine – Singer 7258.

 

 

THREADING THE TOP THREAD

A. Raise the presser foot lifter. Always be sure to raise the presser foot lifter before threading the top thread. (If the presser foot lifter is not raised, correct thread tension cannot be obtained.)

 

B. Turn the hand wheel toward you until the needle is in its highest position.

 

C. Thread the machine with your left hand while firmly gripping the thread with your right hand in the following order as illustrated.

* Guide the thread through thread guide (1 ), and then pull it into the pre-tension guide (2).
* Pull the thread into the tension discs (which are located inside the machine) by first passing the thread to the left of plate (2). Then guide the thread to the bottom of the groove.
* Do a U-turn around the inside of the tab (3).
* Pass the thread through the thread take-up ( 4) from right to left.
* Pull the thread into the inside of the take-up lever until it reaches the eye of the lever.
* Guide the thread into the thread guide (5).
* Pass the thread through the eye of the needle (6) from front to back. (See following page for instructions on operation of the Automatic Needle Threader.)

 

 

IMPORTANT:
To verify that the machine is threaded properly in the tension discs, do this simple check:
1.) With the presser foot raised and the needle unthreaded, pull the thread. You should detect only a slight resistance and little or no deflection of the needle.
2.) Now lower the presser foot and again pull the thread towards the the back of the machine. This time you should detect a considerable amount of resistance and much more deflection of the needle. If you do not detect the resistance, this means you have not threaded the machine correctly and need to rethread it. .

 

 

How to thread a sewing machine – Singer 7258.

You can find the complete instruction manual here.

Kenmore 385.17324 sewing machine threading instructions.

• Raise the thread take-up lever to the highest position by turning the balance wheel counterclockwise.
• Raise the presser foot lifter.
• Place a spool of thread on the spool pin, with thread coming off as shown.

1. Draw the end of thread around the upper thread guide.

2. While holding the thread near the spool, draw the end of the thread down around the check spring holder.

3. Firmly draw the thread up from right to left over the take-up lever and down into the take-up lever eye.

4. Slide the thread behind the needle bar thread guide on the left.

5. Thread the needle from front to back or use the needle threader.

Kenmore 385.17324 sewing machine threading instructions.

You can find the complete instruction manual here.

Kenmore sewing machine manuals

Janome 318 – 319 Sewing Machine Threading Instructions.

 

 

Raise the thread take-up lever to the highest position by turning the balance wheel towards you.

Raise the presser foot with the presser foot lifter and pass the thread in the order of 1 to 8.

1. Pass the thread through the top cover thread guide.

2. Draw the thread down around the thread guide and into the tension.

3. Then down around the check spring holder.

4. Firmly draw the thread from left to right over the take-up lever and down into the take-up lever eye.

5-6. Then down through the lower thread guides.

7. Slide the thread behind the needle bar thread guide on the left.

8. Thread the needle from front to back.

 

Janome 318 – 319 Sewing Machine Threading Instructions.

You can find the complete instruction manual here.

 

Janome sewing machine manual PDF Downloads

 

 

Singer 328 Sewing Machine Threading Instructions.

Threading the Machine

Raise the take-up lever to its highest position by turning the handwheel toward you.
Raise the presser foot.
Place a spool on the spool pin as shown, with thread coming from back of the spool.

 

1. Draw the thread into thread guide using both hands.
2. While holding the thread near spool, draw thread down into the tension area and then around the check spring holder.
3. Firmly draw the thread up and through the take–up lever from right to left.

4. Then draw the thread down and slip it into needle bar thread guide on the left.
5. Thread the needle eye from front to back.

 

You can find the complete instruction manual here.

 

Singer 328 Sewing Machine Threading Instructions

 

 

New Home Janome JW5622 Sewing Machine Threading Instructions.

Threading the Machine

Raise the take-up lever to its highest position by turning the handwheel toward you.
Raise the presser foot.
Place a spool on the spool pin as shown, with thread coming from back of the spool.

 

1. Draw the thread into thread guide using both hands.
2. While holding the thread near spool, draw thread down into the tension area and then around the check spring holder.
3. Firmly draw the thread up and through the take–up lever from right to left.

4. Then draw the thread down and slip it into needle bar thread guide on the left.
5. Thread the needle eye from front to back.

 

You can find the complete instruction manual here.

 

New Home Janome JW5622 Sewing Machine Threading Instructions