Sewing machine threading instruction

Singer 7442 Sewing Machine Threading Instructions.

 

 

Threading Your Machine.

A. Raise the presser foot lifter. Always be sure to raise the
presser foot lifter before threading the top thread. (If the
presser foot lifter is not raised, correct thread tension cannot
be obtained.)

B. Turn the hand wheel toward you until the needle is in its
highest position and the thread take-up is visible.

C. Thread the machine with your left hand while firmly gripping
the thread with your right hand in the following order as
illustrated.
* Guide the thread through thread guide (1), and then pull it
into the pre-tension guide (1a).
* Pull the thread into the tension discs, passing the thread to
the left of plate (2). Then guide the thread to the bottom of
the groove.
* Do a U-turn around the inside of the tab (3).
* Pass the thread through the thread take-up (4) from right
to left.
* Pull the thread into the inside of the take-up lever until it
reaches the eye of the lever.
* Guide the thread into the thread guide (5).
* Pass the thread through the eye of the needle (6) from
front to back. (See following page for instructions on
operation of the Automatic Needle Threader.)

IMPORTANT:
To verify that the machine is threaded properly in the
tension discs, do this simple check:

1.) With the presser foot raised, pull the thread towards the
back of the machine. You should detect only a slight
resistance and little or no deflection of the needle.

2.) Now lower the presser foot and again pull the thread
towards the the back of the machine. This time you
should detect a considerable amount of resistance and
much more deflection of the needle. If you do not detect
the resistance you have miss-threaded the machine and
need to re-thread it.

 

 

Singer 7442 Sewing Machine Threading Instructions

 

You can find the complete instruction manual here.

Janome JD1822 Sewing Machine Threading Instructions.

 

 

Threading Your Machine.

Raise take-up lever to its highest position by turning balance wheel toward you.
Raise presser foot.
Place spool on spool pin as shown, with thread coming from the back of the spool.

1. Draw thread into thread guide using both hands.
2. While holding thread near spool, draw thread down into the tension area and
then around the check spring holder.
3. Firmly draw thread up and through take-up lever from right to left.
4. Then draw thread down and slip it into the lower thread guide.
5. Draw thread down and slip it into needle bar thread guide.
6. Thread needle eye from front to back.

NOTE: You may want to cut the end of thread with sharp scissors for easier needle threading.

 

 

Janome JD1822 Sewing Machine Threading Instructions

 

You can find the complete instruction manual here.

JD 1822
Janome/New Home

Bernina 1630 Sewing Machine Threading Instructions.

Bernina 1630 Sewing Machine Threading Instructions.

Threading Instructions

Threading the upper thread:

A) Turn the power switch to 0.
B) Check that the needle is fully raised.
C) Raise the presser foot. Place thread spool on one of the spool holders and hold while threading.
D) Slip the thread into the first guide on the back of the machine and then take it through the long slit on the thread tension (fig. 1).
E) Take the thread down through the long slot A on the front of the machine, slip it into the thread regu­lator B, up into the slit of the thread take-up C and down
again to the thread guide D on the needle clamp (fig. 2).
F) Thread the needle from front to back.
G) The eye of the needle is easy to see against the white plate on the presser foot shaft. Pull the thread approx. 10 cm (4 “) through the needle.

 

When using special threads such as metal or embroi­dery threads which wind quickly off the spool, thread the supplementary guide on the handle to control the thread feed.

When using the supple­mentary guide, take the thread directly from the spool to the guide and raise the handle (fig. 3). Continue threading as described above.

 

Bringing up the lower thread

1) Turn the power switch to 1
2) Hold the end of the upper thread and sew a stitch by tapping the foot control once. Pull the upper thread to bring the lower thread up through the stitch plate hole (fig. 1). Take both threads through the slot in the presser foot and to the side of the foot.
Instead of tapping the foot control, the lower thread can be brought up by turning the handwheel forwards until the needle is in its highest position .

 

Bernina 1630 Sewing Machine Threading Instructions

 

You can find the complete instruction manual here.

 

 

 

Threading Your Singer 503 Sewing Machine.

Threading Instructions

   1) Turn hand wheel to raise take-up lever to highest point.

   2) Raise stitch chart cover and place thread on either of the two spool pins.

  3) Lead thread through all threading points shown, including the thread control.

  4) Thread needle from front to back.

  5) Draw sufficient thread through eye of needle with which to start sewing.

 

The automatic thread control, located above the tension, ensures a smooth flow of thread
from spool to needle. This device eliminates spool weight and drag by pulling off a
measured amount of thread before it passes through the tension discs.

CAUTION: On Console Models, make certain that Stitch Chart is closed before lowering
machine into cabinet.

 

Threading Your Singer 503 Sewing Machine.

 

You can find the complete instruction manual here.

 

 

 

Threading Your Kenmore 385.16126200 Sewing Machine.

 

 

Raise the thread take-up lever to its highest position by
turning the handwheel counterclockwise.

• Raise the presser foot lifter.

• Place a spool on the spool pin, with the thread coming
off as shown.

 

1) Draw the end of the thread around the upper thread guide.

2) While holding the thread near the spool, draw the end of
the thread down around the check spring holder.

3) Firmly draw the thread up from right to left over the
take-up lever, and down into the take-up lever eye.

4) Slide the thread behind the needle bar thread guide on
the left.

5) Thread the needle from front to back, or use a needle
threader.

 

 

Threading Your Kenmore 385.16126200 Sewing Machine.

 

You can find the complete instruction manual here.