Elna 830 Expressive Sewing Machine Threading Instructions.

 

 

 

Elna 830 Expressive Sewing Machine Threading Instructions

Note: Before starting, ensure that the machine is turned off and unplugged for safety.

Threading the Machine:

Raise the presser foot lifter
Press the lockout key to lockout the machine
Turn the handwheel toward you to raise the needle at its highest position.
(Fig 1) Lockout key
Pass the thread in order from (1 to 7)
.
1. Pull the thread from the spool.
Hold the thread with both hands and pass the thread
into the slit of the pre-tension thread guide. (Fig 2)

2. Wind the thread around the pre-tension thread guide once as shown.
Draw the thread around the corner of the upper thread guide.
Firmly pull the thread toward you along the right channel until the thread snaps.
(Fig 3) Pre-tension thread guide
(Fig 4) Upper thread guide
(Fig 5) Right channel.

NOTE:
If the thread slips out of the pre-tension thread guide
while sewing, wind the thread through the hole as
shown (Fig 6) when threading through the pre-tension
thread guide.

NOTE:
If the thread coming out from the needle eye is too
short alter auto thread cutting and skipped stitch
occurs, draw the thread through the pre-tension
thread guide as shown (Fig 7).

3. Draw the thread down along the right channel and around the bottom of the thread guide plate.
Pull the thread up along the left channel.
(Fig 5) Right channel
(Fig 8) Thread guide plate
(Fig 9 Left channel.

4. While holding the thread at the spool, firmly draw the thread up and to the back of the take-up lever.
Draw the thread forward to draw it into the eye of the take up lever.
(Fig 10) Eye of the take-up lever.

5. Then pull the thread down along the left channel and through the lower thread guide.
(Fig 11) Lower thread guide.

6. Slide the thread from the right of the needle bar thread guide to the left.
(Fig 12) Needle bar thread guide.

7. Thread the needle with the needle threader (refer to the next page).

Remember to consult the machine’s user manual for additional guidance and specific instructions related to your model. Happy sewing!

Elna 830 Expressive Sewing Machine Threading Instructions

 

You can find the complete instruction manual here.

Necchi HD22 Sewing Machine Threading Instructions.

 

 

 

Necchi HD22 Sewing Machine Threading Instructions

Note: Before starting, ensure that the machine is turned off and unplugged for safety.

1. Bobbin Winding:

a. Place a spool of thread on the spool pin at the top-right corner of the machine.
b. Draw thread from spool. Pass the thread through the top cover thread guide.
c. Guide the thread around the bobbin winder thread guide.
d. Insert the thread through the hole in the bobbin, threading from the inside to the outside.
e. Put the bobbin on the bobbin winder spindle, and push it to the right.
f. While holding the handwheel with your left hand, turn the stop motion knob toward you with the right hand.
g. With the free end of the thread held in your hand, depress the foot control.
h. Stop the machine when it has made a few turns, and cut the thread close to the hole in the bobbin.
i. Depress the foot control again. When the bobbin is fully wound, it will stop automatically.
j. Return the bobbin winder to its original position by moving the spindle to the left and cut the thread
k. Tighten the stop motion knob to engage clutch.

Threading the Upper Thread:

Take the spool pin holder and insert it into the hole at the top of the machine.
Raise the thread take-up lever to the highest point by turning the handwheel towards you.
Raise the presser foot with the presser foot lifter and pass the thread in the order from 1 to 8.
1. Pass the thread through the top cover thread guide.
2. Draw the thread around the thread guide and down into the tension.
3. Then down around the check spring holder.
4. Firmly draw the thread from left to right over the take-up lever and down into the take-up lever eye.
5-6. Then down through the lower thread guide.
7. Slide the thread behind the needle bar thread guide on the left.
8. Thread the needle from front to back.

3. Threading the Bobbin Case:

a. Open the hinged cover to access the bobbin case.
b. Insert the bobbin into the bobbin case, ensuring it rotates counterclockwise when pulled by the thread.
c. Pull the thread through the slit in the bobbin case, leaving a tail of thread.
d. Place the bobbin case into the machine, aligning the marks on the case with the markings inside the bobbin case area.
e. Close the hinged cover, making sure it clicks into place.

4. Final Steps:

a. Hold the upper thread and manually turn the handwheel toward you to lower the needle into the fabric.
b. Pull the upper thread slightly to bring up the bobbin thread.
c. Hold both threads together and pull them towards the back of the machine, under the presser foot.
d. Your Necchi HD22 Sewing Machine is now threaded and ready to sew!

Remember to consult the machine’s user manual for additional guidance and specific instructions related to your model. Happy sewing!

Necchi HD22 Sewing Machine Threading Instructions

 

You can find the complete instruction manual here.

Janome 712T Sewing Machine Threading Instructions.

 

 

 

Janome 712T Sewing Machine Threading Instructions

Note: Before starting, ensure that the machine is turned off and unplugged for safety.

1. Bobbin Winding:

a. Place a spool of thread on the spool pin at the top-right corner of the machine.
b. Take the thread and guide it around the thread guide located on the top of the machine.
c. Pull the thread end through the bobbin winder tension disc, located on the top-left side of the machine.
d. Take an empty bobbin and place it onto the bobbin winder spindle, which is situated on the top-right side of the machine.
e. Push the bobbin winder to the right to engage it.
f. Hold the thread end and start the machine. The bobbin will wind automatically. Stop when the bobbin is full or as desired.
g. Cut the thread, slide the bobbin winder to the left to disengage it, and remove the bobbin from the spindle.

2. Threading the Upper Thread:

a. Take the spool pin holder and insert it into the hole at the top of the machine.
b. Place a spool of thread onto the spool pin holder.
c. Pull the thread and guide it around the thread guide located at the top-right corner of the machine.
d. Take the thread and bring it down through the thread guide located at the top-left corner.
e. Guide the thread from the left to the right into the thread tension discs.
f. Pull the thread down and around the take-up lever, which is a metal hook located on the left side of the machine.
g. From the take-up lever, guide the thread straight down and pass it through the thread guide located just above the needle.
h. Thread the needle from the front to the back, leaving a tail of thread.

3. Threading the Bobbin Case:

a. Open the hinged cover to access the bobbin case.
b. Insert the bobbin into the bobbin case, ensuring it rotates counterclockwise when pulled by the thread.
c. Pull the thread through the slit in the bobbin case, leaving a tail of thread.
d. Place the bobbin case into the machine, aligning the marks on the case with the markings inside the bobbin case area.
e. Close the hinged cover, making sure it clicks into place.

4. Final Steps:

a. Hold the upper thread and manually turn the handwheel toward you to lower the needle into the fabric.
b. Pull the upper thread slightly to bring up the bobbin thread.
c. Hold both threads together and pull them towards the back of the machine, under the presser foot.
d. Your Janome 712T Sewing Machine is now threaded and ready to sew!

Remember to consult the machine’s user manual for additional guidance and specific instructions related to your model. Happy sewing!

Janome 712T Sewing Machine Threading Instructions

 

You can find the complete instruction manual here.

Kenmore 385.18330990 Sewing Machine Threading Instructions.

 

 

 

Threading Instructions

* Raise the thread lake-up !ever to its highest position by turning the handwheel counterclockwise.

* Raise the presser foot lifter.

* Place a spool on the spool pin, with thread corning off as shown.

 

1. Draw the end of thread around the upper thread guide.

2. While holding the thread near the spool, draw the end of the thread down around the check spring holder.

3. Firmly draw the thread up from right to left over the take-up lever and down into the take-up lever eye.

4. Slide the thread behind the needle bar thread guide on the left.

5. Thread the needle from front to back or use a needle threader.

 

Kenmore 385.18330990 Sewing Machine Threading Instructions

 

You can find the complete instruction manual here.